GT Cleaner is tough on dirt and gentle on floors. GT Cleaner leaves no residue, will not haze sport finishes and should be used as a daily cleaner. GT Cleaner is also the final cleaning step in the TyGlu System.

• Versatile - use for daily and periodic maintenance.
• Cleans and removes abrasive soils.
• Fast drying.
• Leaves no residue.
• Maintenance Cleaner for Wood Floors

APPLICATOR REFILLS Refill pads for T-Bar applicators. Use with water-based and OMU coatings

Floor Finish Applicator Bar Medium weight T-Bar floor coater that provides consistent and even coverage. Applies a thicker coat. For use on sport and commercial wood floors. 24''W, Applicator Refills (Pkg u/m = 6/cs Sold By u/m = Case)

Americo's Sand Screen Discs are commonly used for removal or repair of coatings on wood floor surfaces. An ideal application would be refinishing gym floors. They are also used for repair of painted floor surfaces. Use both sides of the Sand Screen Disc.either wet or dry.

All Sport One is a one component clear waterbased sport finish specifically formulated for sports floor applications. All Sport One provides a completely colorless finish with exceptional durability and chemical resistance without the use of an external catalyst.

• One Component
• Colorless, Clear Finish Clarity
• Excellent Chemical and Perspiration Resistance
• Easy to Maintain
• Clear Waterbased Sport Finish

HP Gym Coat is specifically designed for sports floors combining innovative floor coating technology at a great value. Durable, fast-drying and low VOCs, HP Gym Coat provides high gloss and extended durability. Also, the clear finish lets the natural beauty of the wood shine through.

• Superior traction for sports floors. |Easy clean up with water. |Dries to a clear film. |Fast drying/low odor |Ultra durable.

PREPARATION: FOR NEW OR SANDED FLOORS: Prepare the floor using accepted NWFA or MFMA procedures. Vacuum all dust and tack with cotton towel. All residue must be removed. Apply water-based wood sealer following instructions on sealer label: 2 coats minimum.

FOR SCREENING AND RECOATING: Always clean the floor prior to screening. Mix Betco GT Cleaner at 32 oz./gal. or 250 mL/L (1:4) with water and tack using a clean towel. Screen using new 100 or 120 grit screens or higher, vacuum and tack using a water moistened cotton towel.

APPLICATION: While stirring product, add catalyst slowly and continue mixing for 30 seconds. Mix thoroughly and let stand for 10 minutes. Once catalyzed, pot life is 12 hours. Apply at 600 - 700 sq.ft./gal. Pour finish into a clean, dry, plastic pour can. Pour a 4-inch wide line of finish along one wall with the grain of the wood. With applicator at a slight angle, move the puddle line to the opposite wall, always maintaining a wet edge. At the end of each pass, make a smooth turn with the applicator and squeeze out excess finish with the grain next to the puddle line. Allow to dry thoroughly (minimum 3 hours between coats depending on conditions with a maximum of 24 hours). Abrade between coats if 24 hours has elapsed with a maroon top scrub pad or 120 grit screen. Apply 2 coats minimum. Allow light traffic after 24 hours, however, it is susceptible to scuffing and marring.

Please recycle empty containers. NOTE: Allow adequate ventilation. Circulate air above the floor. Allow adequate airflow for at least 24 hours after final coat is applied. Use air conditioners and exhaust fans where available. NOTE: Slip resistance meets or exceeds (ASTM D 2047-11) James Machine 0.5 minimum.

• Viscosity: 30 centipoise |Color (dried): Clear |Warranty: 1 year |Coverage: 700 - 800 square feet/gallon |Rubber burn resistance: Excellent |Solids: <34% |Weight per gallon: 8.69lbs. |Flash Point: None |Recoat time: 12 hours |Dry time: 3 - 6 hours minimum |VOC's: <350 g/L |Pot life: 12 hours